Cell therapies present unique challenges when complying with this paradigm for several reasons only two of which I will mention here.  Firstly, it is not possible to achieve the level of product purification as one might with other therapeutic products.  Secondly, the product characterization is at a cellular rather than molecular level.

Autologous cell therapies present another set of unique challenge in this paradigm because of the notable patient-to-patient variability where the patient is also the donor of the raw material.  This often means there is a wider tolerance of heterogeneity in the product but it still must be within what has been proven to the regulatory agency as a safe and effective range.  


In cases where an autologous cell therapy is centrally manufactured, they are most often subjected to product release testing similar to that described above.  One notable difference, particularly for fresh products, is that the products may be shipped to the clinic and even administered before the full panel of test results are obtained.  This wold be considered highly unusual (if ever acceptable) with other types of products but is tolerated because of the time-sensitivity of these products and their high safety profile.


In the case of autologous cell therapy products produced at the bedside there is often not the same kind of product release discipline.  Often the regulatory agencies deal with the product consistency and specification compliance issue by ensuring that the cell processing device used point-of-care is validated to ensure the cellular product output is always within a specified range shown to be clinically safe and effective.


The Varying Degree of Product Characterization/Specification of Autologous GTP Cell Therapy Products


However - and now I get to the point of this blog post - for cell-based products, procedures and/or devices/kits which are not mandated to be formally approved by a regulatory agency before they can be commercially marketed, there is no product specification rigor.  Compliance with the Good Tissue Practice regulations and guidance is deemed to ensure safety.  In the United States, cell-based products which are deemed to be "minimally manipulated" and intended for "homologous use" are typically allowed to go straight to market with no formal approval.  Safety and clinical data is not required but is practically necessary to support physician adoption and, where applicable, reimbursement.  


This means that for these products there is a great deal of variability in terms of how much rigor companies apply in characterizing their product and then ensuring that each batch complies with the specifications they themselves have determined to be safe and effective. Again, where such products are manufactured in a centralized facility the likelihood of some release testing is greater.  However, those companies relying on a point-of-care processing kit or device business model that has not been deemed to require formal market approval, rarely (if ever) include product release testing.


The common criticism of these companies is that they simply do not know what they are injecting into patients because of the combination of the patient-to-patient donor variability, the lack of any disciplined product characterization or dosing studies, and the absence of any product release testing.  


This criticism is not equally levied at all autologous GTP products or companies - even those relying on point-of-care processing.  Of course some companies care and do a lot to try to ensure their product is well-characterized and that each batch complies with product specifications. This may involve the use of product release tests but can also involve the combination of pre-market research into the product characterization, safety, and dosing along with validation of the device/kit output.  In this way a company can say that within a very small margin, the output will be within the product specifications the company knows is safe and efficacious.


However, in a rush to get their device/kit to market some companies appear to care very little about the cell product characterization, validation of the output of their device/kit, or tying this data to optimal dose.


More concerning are those companies that appear to provide such data but it is wrong or meaningless.  What follows appears to potentially be a case study of precisely this problem. 


The INCELL Study 


This week I came across a fascinating white paper from Incell Corporation analyzing the output of adipose tissue processing kits of MediVet-America apparently demonstrating the inaccuracy of their cell counts (a common type of cell therapy product characterization) and calling into the question the cell count claims of Intellicell Biosciences (New York, NY) and Adistem (Hong Kong).


At the heart of the critique is the claim that the cell counting (product characterization) techniques employed by these companies counts as cells things (namely acellular micelles) which are not cells.

I encourage you to read the white paper in its entirety.  They corresponding author told me to watch for one or more papers which they are preparing for submission to peer-reviewed publications shortly.  Presumably these will rely on a larger data set and perhaps test other methodologies or technologies.


For the purposes of this blog, I've pulled what I believe are the most salient excerpts below:

Intrigued by the high cell numbers  (5 to 20 million cells/gram)  reported by kit/device manufacturers such as MediVet-America (Lexington, KY), Intellicell  Biosciences (New York, NY), and Adistem, Ltd. (Hong Kong) in adipose stem cell therapy compared to other methods (e.g., 
Chung,Vidal, and Yoshimura), INCELL staff conducted a research study to  investigate the high apparent yield of stem cells.  This initial work was focused  on SVF cells from the MediVet Kit, which is marketed to isolate adiposederived canine SVF and stem cells.

The cell yields reported for the Medivet Kits are five to more than ten times higher than the yields routinely obtained by INCELL from freshly harvested human or animal adipose tissue using our adipose tissue processing methods.  These yields are also tenfold or higher than those reported in the literature by most academic researchers (Chung-canine, Vidal–equine, Yoshimura–human).  Since these  cell counts are used to support stem cell dosing recommendations and cell banking, it is important to better understand why the cell numbers are higher.

...

A comparative analytical study of three dog donors of adipose tissue was designed to evaluate the cell yields using the MediVet Kit as an example of this class of isolation system. All  kit procedures were followed as per the instructions provided.  A brief overview of the different cell counting methods used, and the resultant cell counts, observations and explanations of the results observed, are described below

....

This study shows that incorrect counting of adipose derived SVF cells and the subset of regenerative stem cells can subsequently result in inaccurate dosing, both in direct therapeutic applications and in cryostorage of cells for future use.  The DAPI-hemocytometer cell count (manual) was considered the most accurate, but there are various sources of technical difficulties that  can lead to incorrect  cell numbers. The nature of adipose tissue itself with variability in dissociation by enzymatic digestion can all contribute to the outcomes. Fat tissue has a propensity to form acellular micelles and oils upon tissue disruption. Processing methods or reagents (e.g., Solution E or lecithins) can generate micelles that may be  erroneously  counted as cells. Autofluorescence and dye trapping or uptake by the micelles can lead to very high inaccurate cell counts when automated cell counting is used. 

In this study the most inaccurate counting came from the Cellometer. When used according to kitrecommended guidelines and on-site training provided by Nexelcom for counting  cells by the MediVet procedure, the Cellometer overstated the DAPI-hemocytometer cell count by up to 20X or more. The Coulter Counter protocols also led to incorrect, high cell numbers. Although the cell counts were still a bit high, the authors recommend the NucleoCounter, or similar equipment, as more acceptable for automated counting.  The manual hemocytometer-DAPI method is the most accurate, but requires a highly experienced cell biologist or technician to make accurate counts and  is not suitable for routine clinical use. 

...

Other companies also have claims of very high cell numbers when their processes are used. Adistem, like MediVet, states they add an emulsifying agent to their kits to assist in cell release, and they also use a light activation system. Their kits were not tested in this study but it is possible that the high cell numbers reported by Adistem are also incorrect and result from the same problems highlighted in this paper for the MediVet procedure. Ultrasonic energy, which is commonly used to manufacture micellular  liposome  structures and to disrupt and lyse cells, is  another potentially problematic procedure for counting and verifying viable, regenerative cells.  Intellicell 3uses ultrasonic energy to release cells from adipose tissue, and it is possible that resultant micelles or cell fragments contribute to the higher than expected cell numbers.  This assumption could be verified with additional studies.  

In summary, the authors caution that great care must be taken when using kits and automated cell counting for stem cell dosing and cryobanking of cells intended for clinical use. Overestimated  cell numbers would be a major confounding source of variation when efficacy of stem cells injected are compared as doses based on cell number and when cryostored cells are aliquoted for use based on 

specific cell numbers as a treatment dose.  Hopefully, this study will lead to more  reproducible counting and processing methods being reported in the literature, more inter-study comparability of cell doses to clinical outcomes,  more industry diligence to support claims, and more accurate counting for dosing stem cell therapies to patients.

...

Chung D, Hayashi K, Toupadakis A, et al.  Osteogenic proliferation and differentiation of canine bone marrow and adipose tissue derived mesenchymal stromal cells and the influence of hypoxia.  Res Vet Sci, 2010; 92(1):66-75. Vidal MA, Kilroy GE, Lopez MJ, Johnson JR, Moore RM, Gimble JM. Characterization of equine adipose tissue-derived stromal cells: adipogenic and osteogenic capacity and comparison with bone marrow-derived mesenchymal stromal cells. Vet Surg, 2007; 36:613–622.  Yoshimura K, Shigeura T, Matsumoto D, et al:  Characterization of freshly isolated and cultured cells derived from the fatty and fluid portions of liposuction aspirate.  J Cell Phys, 2006; 205:64-76.

http://www.celltherapyblog.com hosted by http://www.celltherapygroup.com

Source:
http://feeds.feedburner.com/CellTherapyBlog